About Wicks & Wires
Learn more about Wicks & Wires and our mission statement.
Virtual Tour
Take a virtual tour of our store!!
What's New
Flow Ti Atty - Odis Collection
Sold Out
The Flow Ti Atty is designed for use in the ever so popular Billet Box Rev4’s. This atomizer features a postless design in order to provide a spacious deck for larger builds. To allow adequate air flow, the inlet has been moved to one side so that in combination with a chamfered edge, the air can be redirected and unobstructed by posts. For ease of building, the base of the Flow Ti has 510 threading where the adjustable air flow ring will also be located. There are cutouts on the lower half of the two piece chimney for sufficient wicking. The opening is wide enough to have the option of keeping the ends of the wicks tucked within the chamber, or protruding from the outside of the atomizer and into the tank. In order to prevent the lower half of the chimney from rotating, there is a locator that rests within an indent on the air flow inlet. Along with the stock chimney, a second option will be available with a wider inner diameter to allow for a looser draw. The Flow Ti is constructed from high grade titanium with PEEK and Delrin for the insulator and air flow control ring. Included in the packaging there will also be an Ergo 510 with a design unique to our standard model.
Specs
- Titanium, Delrin, and PEEK construction
- Chamfered air flow
- Postless design
- Adjustable air flow
- 2 piece chimney
- 510 base
- Finned Ergo 510 drip tip included, as well as a secondary chimney with a wider bore
O-Atty V2 - Odis Collection
$134.99
The O-Atty v2 is an adaption of Odis Collection & Design’s first RDA, the original O-Atty v1. The layout of the build deck has been redesigned with a 4 post system which uses grub screws without the use of clamps. This will allow for easier installations of either single or dual coil builds. Our signature angled air flow is still within the design to gather the vaper from below the coils and then surrounding it entirely on its way up towards the drip tip. The deck is now concaved which is better suited for when the included bottom feeder pin is installed to drain any excess e-liquid. The top cap is now two parts which incorporate air flow adjustment, as well as a single air hole option. To prevent rotation of the top cap when adjusting the air flow, there are locators around the deck to help keep it in position. Contacts, posts, and center pins are 24Kt gold-plated.
Specs
- 316 Stainless steel, Delrin, and PEEK construction
- 22mm diameter
- Gold plated hardware
- Signature angled air flow channels
- Concave deck
- BF Pin included
- Updated 4 post design
- 2 piece top cap
- Adjustable air flow
- BF Pin included
VT75C 26650 Evolv DNA75C (Color) Mod - HCigar
$159.99
The HCigar VT75C is the first product to use the brand new Evolv DNA75 Color chip!
Housed in an ergonomically designed attractive housing with genuine leather accents and an aluminum alloy frame with stainless steel caps, the DNA75 Color chip now brings a full colour TFT screen to Evolv's product line up, while allowing extensive customization of the mod UI, from screen backgrounds, colour schemes, and various pieces of information.
Also new to the DNA75 Color board, is an extended 9 volt output, allowing users to push higher wattage out of higher resistance builds that the standard DNA75 chip could not do.
Other improvements over the standard HCigar VT75, include:
- Stainless steel battery cap design, with more robust threads for greater durability and strength.
- Anti-leak design in the 510 connector, to prevent leaking atomizers from fouling the internals.
While the HCigar VT75C sold from most locations has the factory firmware settings (stock Evolv settings with nothing more than a VT75C logo attached), all units leaving Wicks & Wires Vape Shoppe will have fully customized settings already uploaded, which include a couple of important settings unique to the VT75C only:
- Mod internal resistance (provides more accurate power output and temperature control)
- Enclosure's thermal properties (heating and cooling constants, etc)
- Battery analyzer run for the BrilliPower 5000mAh 85A 26650 battery.
Additional customizations applied by Vapes by Enushi technicians include:
- Multiple material type profiles already installed so that users can immediately use the device right out of the box, including Kanthal A-1, Nichrome 80, Nickel 200, titanium grade-1, 316 stainless steel, and 317 stainless steel.
- Temperature dominance turned on for all profiles that utilize temperature capable materials.
- Status LED programmed to identify charge status, when firing, and when on standby.
- Screen timeout shortened to conserve battery power.
- Screen display re-arranged to display more valuable data (resistance, battery voltage, set temperature/wattage, and set wattage/temperature.)
Powered by a single 26650 cell or 18650 cell (with the use of the included size adapter), this mod outputs up to 75 Watts, while including all of the programmable features of the Evolv eScribe software for a fully customizable device with over 100 different adjustable settings! Download the newest version of EScribe 2.0 that supports the DNA75 Color chip >>HERE<<.
Powered by a single high discharge IMR 26650 or 18650 cell, this device packs enough power to get you through the day! Evolv's DNA75 Color specifications strictly states a requirement of batteries that can handle a continuous current discharge rating of 28 Amps or higher. We can currently recommend Brillipower 5000mAh 85A 26650 cells (maroon color) as the best 26650 to be used, which can be purchased >>HERE<<.
NOTE: DO NOT over tighten the battery cap, or it may cause the frame to bend. Only enough pressure is required to snug the cap up against the battery to close the circuit.
The brand new Evolv DNA75 Color chip is the heartbeat of this feature packed, compact, and powerful mod! Featuring a full set of features including variable wattage from 1 Watt to 75 Watts of output power, temperature control on many common as well as uncommon wire material types, hybrid material coils, and a fully integrated software suite that allows the user to connect the device to a computer for full customization of all features and display screens for the unit!
New to the DNA75 Color
Along with all of the features of the standard DNA75 board, the new DNA75's most notable difference, is the inclusion of a full colour TFT screen, that allows full customization of screen data, wallpapers, and colour schemes. Also new to the DNA75 Color, is the ability to push an extended 9 volts output!
The Evolv DNA75 Color regulated variable wattage power control board has temperature control features through voltage step up/down topology.
1 year limited warranty, taken care of directly through your vendor or directly through HCigar.
- 1 Year warranty on Evolv DNA75 Color chip (taken care of directly through Evolv)
- 7 Day warranty on HCigar enclosure and any other manufacturing defects.
Contact your vendor for exact details on warranty limitations.
The newest Evolv DNA75 Color board on this device has many of the well known features of the previous DNA75 board, such as the following features:
- Large full colour TFT screen displays the set wattage level, atomizer resistance, battery level indicator, firing voltage, and more. All of this information is completely user customizable in this DNA75 Color board!
- "Atty Lock" function to disable refinement - optional, and user customizable through software.
- Power regulation, to maintain a consistent power output, regardless of the charge status of your battery.
- Voltage step down technology via a buck chip allows the device to pull voltage below the natural charge state of the battery. What this means, is the ability to put a very low resistance atomizer on the device, while still be able to fire at very low wattage. This is a great feature when you want to take a break from huge wattage cloud chucking and relax with some low wattage puffing from your low resistance setup!
- Variable wattage control, up to 75 Watts! TRUE 75 Watts of DC power output! No "rattlesnake" effect that you would get with PWM (Pulse Width Modulation) devices, the DNA75 offers true and clean 75 Watts of power output! When used with temperature protection turned on, the wattage control acts as your accelerator, which dictates how fast your coil will get up to temperature.
- Temperature control / protection technology, which has a way to calculate the approximate temperature of your coil. By setting a maximum temperature limit cut off point, the chip knows to pull back on the power (wattage/voltage) output so that the temperature does not exceed your set cut off. Many benefits of this include:
- No more dry hits!
- No more burnt wicks, even when your wick is completely dry! Finally, a way to vape till the very last drop!
- Avoid putting so much heat to your liquid that you begin creating dangerous free radicals and off-chemicals!
- Increased battery life!
*Note: Nickel Wire (Ni-200), ResisTherm (NiFe30), SS316, SS317L, or Titanium Grade-1 Wire is required to build your coils, in order to activate the temperature control features.
Spring loaded floating 510 silver plated brass center pin for maximum electrical conductivity and consistent accurate connection.
Built in micro USB charger allows pass-thru charging/vaping.
Specifications:
- Output Power: 1 to 75 Watts
- Accepted Standard Resistance: 0.1 Ohms to 2.0 Ohms
- Accepted Temperature Control Resistance (cold reading): 0.08 Ohms to 1.0
- Output Voltage: 1 to 9 Volts
- Maximum 50A output
- Temperature Limit: 200°F to 600°F or 100°C to 300°C
- Product size (L x W x H) :
Functions:
- Lock
- Unlock
- Stealth Mode
- Display Rotation
- Temperature Adjustment
- Temperature Display in Celsius or Fahrenheit
- Atty Lock
- Screen display, all functions, and all features are adjustable via software suite.
Jack Knife - SOAK
$19.99
Deep fried sesame seeds and sweet creams for a taste sensation unlike anything you've tried before!!!
PG/VG: 30/70
View full product details
Hussar Torpedo Micro LE (Limited Edition) RTA - Hussar Vapes
$242.99
The Hussar Torpedo Micro LE (Limited Edition) is a Polish made high end RTA (Rebuildable Tank Atomizer) that features amazing flavour reproduction, generous cloud performance, easy build, easy wicking, juice flow control, easy fill capabilities, air flow control, and adjustable 510 pin height.
This Limited Edition Torpedo release of the Hussar RTA has a couple of differences, which comes with these configuration changes:
- Torpedo cap which accepts 510 drip tips (drip tip not included)
- Micro Ultem tank & chimney (rather than full sized)
- Gold plated single coil deck
- New wooden packaging that was first released with the Hussar RDTA.
This Single Coil Deck version of the Hussar RTA comes with an easy to build single coil deck with wire trap walls and large screw heads to make rebuilding easier.
The Ultem tank which comes with this RTA has a number of benefits, including increased heat resistance, durability, and can withstand aggressive liquids that are known to crack polycarbonate and acrylic tanks.
Juice flow control is easy to use, with a slight twist of the Ultem tank section.
Air flow control is easy to manage, adjusting the cyclops style air flow inlet from wide open for a slightly restricted lung hit, to fully closed down for mouth-to-lung performance.
Refilling liquid is easy; just pop the top cap off, and refill directly in the large juice inlet.
A narrow chimney and a conical bell design allows flavour and vapour to focus directly to the user.
WARNING: It is highly recommend that you fully clean out this product before the first time you use it. While the factory does a decent job at removing dust, shavings, machining lubricants and greases, there is still the potential for trace elements to remain, and it is best recommended that you do an additional cleaning to meet your standard of cleanliness.
DISCLAIMER: Rebuildable atomizers are for experienced vapers with access to meters and a working knowledge of Ohms Law, Watts Law, battery safety, and how general electricity works. Please ensure care is taken as to not cause damage nor harm to the atomizer, your battery, the vaping device, yourself, others, or personal property.
Wicks & Wires Vape Shoppe is not responsible for misuse of product, or dangerously low coil builds. Wicks & Wires Vape Shoppe is not liable for the use of improper batteries for your builds.
View full product details
Hussar RDTA Rebuildable BF Capable Atomizer - Hussar Vapes
$189.99
The Hussar RDTA by Hussar Vapes is a Polish made high end rebuildable tank atomizer that features amazing flavour reproduction, generous cloud performance, easy build, easy wicking, easy fill capabilities, air flow control, bottom feed capable (BF pin included), or usable as a standard dripper/tank.
The included bottom feed pin allows users to fill the small capacity tank beneath the deck with the squeeze of a bottle. It can also be used as a standard dripper/tank, via a large easy-to-fill juice inlet with relief valve, by simply pulling the top cap off to access it.
Dripper? Tank? You decide what you want to call it. It looks small like a dripper, yet holds about 2mL of liquid! The contained reservoir allows you to lay the atomizer on its side without any risk of leaking, just like a tank!
An ultra small evaporation chamber allows vapour production to be condensed for incredible flavour production.
Dual sided air hole inlets allows air to hit both sides of the coil for maximum flavour and cloud production with no hot spots.
Designed for single coil builds.
WARNING: It is highly recommend that you fully clean out this product before the first time you use it. While the factory does a decent job at removing dust, shavings, machining lubricants and greases, there is still the potential for trace elements to remain, and it is best recommended that you do an additional cleaning to meet your standard of cleanliness.
DISCLAIMER: Rebuildable atomizers are for experienced vapers with access to meters and a working knowledge of Ohms Law, Watts Law, battery safety, and how general electricity works. Please ensure care is taken as to not cause damage nor harm to the atomizer, your battery, the vaping device, yourself, others, or personal property.
Wicks & Wires Vape Shoppe is not responsible for misuse of product, or dangerously low coil builds. Wicks & Wires Vape Shoppe is not liable for the use of improper batteries for your builds.
View full product details
KAOS Spectrum 230W TC MOD - Sigelei
$74.99
Introducing the newest dual 18650 mod by Sigelei "The Kaos Spectrum" featuring a 10 to 230W output range, preheat power, and a TFT color screen. The KAOS Spectrum integrates a LED lit bezel surrounding the 0.96 inch screen, and can be set via six colour options or completely disabled if desired. See the promo video by clicking....
-
10 to 230W Output Range 0.1 to 3.0 ohm Atomizer Resistance Range 1 to 7.5W Bypass Mode Preheat Function 35A Maximum Output Current Firmware Upgradeable
-
Temperature Control Suite Ni200 Nickel Support Titanium Support SS316L Support -
Adjustable TCR Fine Tune Temperature Output
Preheat Functionality Resistance Read and Lock 200 to 570 Degree Fahrenheit Range 0.1 to 3.0 ohm Atomizer Resistance Range
-
0.96 Inch TFT Color Display Three Column Display Output Temperature Output Wattage Output Voltage Material and Mode Selection Atomizer Resistance Output Current Battery Life Indicator Adjustment Lock
-
Zinc Alloy Construction Leatherette Back -
LED Color Light Screen Bezel Six Color Options Can be Disabled
-
Three Button Control Oversized Firing Button Adjustment Buttons
-
On Board Charging 2.5A Max Charge Current
-
Hinge and Locking Battery Access Door Gold Plated Connections -
Accepts Two High Amperage 18650 Batteries Sold Separately
-
Stainless Steel 510 Threading Spring Loaded Gold Plated Contact
Low Resistance/Short/Low Battery/Temperature Protection
SMOK T-PRIV 220W TC Starter Kit - SmokTech
$99.99
The SMOK T-PRIV 220W TC Starter Kit exemplifies SMOKTech's commitment of developing innovative output technology, launching a futuristic LED lit within an aggressive exterior design while integrating one of the industry's leading onboard chipset. The SMOK T-Priv 220W TC Box Mod implements a space-age chassis, presenting a unique hardshell with raised edges and Transformer-like details that works in synergy with the light-up LED for a refined showcase piece. The innovative LED Strips around the device are fully customizable, offering a spectrum of vibrant colors that is truly unique for the T-Priv. Inside, SMOKTech has integrated one of the most dynamic internal system, deploying an output range up to 220W and sophisticated temperature control suite. The included TFV8 Big Baby Beast is the premier compact sub-ohm tank in its segment, offering a well-balanced dynamic range with 5mL juice reservoir, precision airflow control, signature hinged top-fill system, and the popular Baby Turbo Engines coil structure. Despite the shorter stature and diminutive in size, the TFV8 Big Baby Sub-Ohm Tank is a compact rendition of cloud-chasing achievement, based on the high performance V8 line. Asserting itself as the premier fully-featured set with top echelon performance prowess, the SMOK T-Priv 220W TC Starter Kit is a must-have collection for all types of vapers.
TFV8 Baby Replacement Coils can be found HERE.
SMOK T-Priv 220W TC Box Mod Features:
Dimensions:86.6mm by 48.1mm by 32mm
Dual High-Amp 18650 Batteries - Not Included
Wattage Output Range: 6-220W
Voltage Output Range: 0.5-9V
Min Atomizer Resistance: 0.06ohm
Temperature Range: 200-600F
Supports Ni200 Nickel, Titanium, and Stainless Steel Heating Elements
9-Colorful LED Strips - Fully Customizable
Intuitive OLED Display
Full Display Matrix - Rich Data Feedback
Stealth Firing Bar Mechanism
Hinged Battery Cover
Intelligent Atomizer Recognition
Puff Monitoring System
12 Seconds Cut-Off
Short Circuit Protection
Over-Heat Protection
Low Battery Warning
MicroUSB Port
510 Connection
Available in Silver, Black, Red, Blue, Purple, Gold, Rainbow
SMOK TFV8 Big Baby Tank Features:
24.5mm Diameter
5mL Juice Capacity
Superior Stainless Steel Construction
High-Grade Glass Reinforcement
Convenient Top-Fill Design with Hinge Lock
Dual Adjustable Airflow Control at Base
Black Delrin Ultra-Wide Drip Tip
Patented Baby Turbo Engines Coil Structure
0.4ohm V8 Baby-Q2 Dual Coil - rated for 30-80W | recommended 55-65W
0.15ohm V8 Baby-X4 Quad Coil - rated for 30-70W | recommended 45-60W
0.15ohm V8 Baby-T8 Octuple Coil - rated for 50-100W | recommended 60-80W
V8 Baby RBA - Two-Post Deck
510 Connection
Includes:
1 TPriv 220W Box Mod
1 TFV8 Big Baby Tank
1 0.4ohm V8 Baby-Q2 Dual Core
1 0.15ohm V8 Baby-T8 Octuple Core
1 Replacement Glass Tube
1 MicroUSB Cable
Spare Parts View full product details
Harambae - 12 Monkeys
$29.99
Harambae features a tangy citrus unison of grapefruit highlights fused with lemon, lime, blood orange and refreshing guava undertones. The zesty and sharp exhale of this citrus synergy will be the savior to your taste buds when everything else feels dull!
PG/VG: 20/80
View full product details
Sherman 28mm RDA - Asylum Mods
$89.99
The Sherman RDA by Asylum Mods is a U.K. designed 28mm rebuildable drip atomizer with a two post clamp style build deck, redirected bottom airflow, and is 810 drip tip compatible. The Sherman RDA is designed to accompany coils up to 2.5mm in width and 2mm in height, making this RDA ideal for build enthusiasts. Under the cap is a wide build deck with two large clamp style posts and redirected airflow channels that are raised above the juice well for enhanced flavor production. The outside of the Sherman RDA features an adjustable bottom airflow control ring, CNC engravings, and a wide bore 810 drip tip in both ULTEM and Delrin options. The Asylum Mods The Sherman RDA is a beautifully designed high end atomizer perfect for those looking for a larger RDA for large format coils.
Product Features:
28mm Diameter
Two Post Build Deck
Center Screw Clamp Style Terminals
Two 2.5mm by 2mm Terminals Per Post
Top Mounted Flathead Screws
PEEK Insulator
6mm Deep Juice Well
Unified Juice Well
Centered Redirected Air Channels
5.5mm by 6mm Each Channel
Air Channels Raised 3mm Above Deck
Adjustable Bottom Airflow
Four Holes Per Side
2mm Diameter Each Airhole
810 Drip Tip Top Cap
Wide ULTEM 13mm Bore Drip Tip
Wide Delrin 13mm Bore Drip Tip
CNC Engraving
Stainless Steel Construction
Silver Plated 510 Connection
Product Includes:
One Asylum Mods The Sherman RDA
One 810 ULTEM Drip Tip
One 810 Delrin Drip Tip
Spare Part Pack
Feast of the Undead - Bombsauce E-Liquid
$31.99
A sweet and succulent blend of exotic fruits perfectly paired with a delicious melon medley.
PG/VG: 30/70
View full product details
Balanced - SVRF
$31.99
A well balanced blend of coconut and creams.
PG/VG: 30/70
View full product details
Refreshing - SVRF
$31.99
A refreshing combination of mango, papaya and cantaloupe.
PG/VG: 30/70
View full product details
Satisfying - SVRF
$31.99
A satisfying raspberry and dragon fruit iced tea.
PG/VG: 30/70
View full product details
AW IMR 18490 1200 mAh Battery
$12.99
Nominal Voltage : 3.7V
Capacity : 1200mAh
Lowest Discharge Voltage : 2.50V
Standard Charge : CC/CV ( max. charging rate 1.2A )
Cycle Life : > 500 cycles
Max. continuous discharge rate : 18A
Operating Discharge Temperature : -10 - 60 Degree Celsius
Dimensions : 18.15 x 49.1 (+/-0.05)mm
View full product details
Coral DNA60 Box Mod - Lost Vape
$149.99
The Lost Vape Coral DNA60 Box Mod is a miniature size box mod powered by an Evolv DNA60 Chip. Featuring a 60W maximum output power, wide temperature control range, waterproof button design and customized 1A charging with cell monitoring.
Batteries for the Lost Vape Coral can be found HERE.
Features
Zinc Alloy Construction
Evolv DNA60 Chip
Output Wattage Range: 1W-60W
TC Control Range: 200°F-600°F
Requires Single 18490/18500 Battery
62mm Height
25mm Width
38mm Length
Waterproof Button Design
Customized 1A Charging
Cell Monitoring
Typhon 510 Drip Tip Adapter - DDP Vape
$20.99
The 510 Drip Tip Adapter for the Typhon RDA is made of black Delrin, and allows users to use standard 510 drip tips with their Typhon.
Fits the Typhon RDA, available for separate purchase HERE.
WARNING: It is highly recommend that you fully clean out this product before the first time you use it. While the factory does a decent job at removing dust, shavings, machining lubricants and greases, there is still the potential for trace elements to remain, and it is best recommended that you do an additional cleaning to meet your standard of cleanliness.
Typhon SCR - Single Coil Reducer - DDP Vape
$27.99
The SCR (Single Coil Reducer) is an accessory for the Typhon RDA, which reduces the chamber size for single coil builds, resulting in greater flavour production.
Made of PEEK for higher heat resistance.
Fits Typhon RDA only, which can be purchased HERE.
WARNING: It is highly recommend that you fully clean out this product before the first time you use it. While the factory does a decent job at removing dust, shavings, machining lubricants and greases, there is still the potential for trace elements to remain, and it is best recommended that you do an additional cleaning to meet your standard of cleanliness.
View full product details
BF Silicone Bottles, 5mL Capacity, Black Delrin - Dee Mods
$23.99
These black Delrin cap smoked black silicone bottles by Dee Mods have a capacity of 5mL with the hose inserted, and are for use in bottom feed (BF) squonk mods.
Fits most devices. Contact us if unsure if it will fit your device.
Three piece cap design prevents leaking, provides a solid seal, and black Delrin construction will not conduct electricity.
View full product details
"Four Horsemen" edition Hammer of God v3.1 - Deathwish Modz + Vaperz Cloud
$279.99
This special edition HOG v3.1 is a collaboration between Deathwish Modz and Vaperz Cloud, and is a limited run.
Combining the striking visuals of Deathwish Modz designer with the powerhouse Hammer of God mod, this unique piece is truly a work of art!
The Hammer of God (H.O.G.) is back and better than ever!! With it's new redesign, the Hammer of God v3.1 is easily the most functionally and ergonomically friendly of the HOG series. Keeping with the parallel-series style of the HOGv2, this mod gives you the hard hitting vape of a series mod but the safety of a parallel circuited device. It truly is the best way to finish the legacy of the Hammer of God Box Mod. This Mammoth of box mods utilizes a FOUR 18650 battery parallel series configuration for the ultimate vaping HAMMER!
WARNING: This device is an unregulated mechanical device at 8.4 Volts that is recommended FOR ADVANCED USERS ONLY. Use at your own risk. Users of mechanical devices must be aware of battery safety and ohms law in order to prevent risk and harm to the device, to person or to property. Be aware, that mechanical mods such as this one do not have any short circuit protection and lack any firing button locks.
Specifications:
- 8.4volts
- Parallel-Series circuit system
- Improved Bottom loading battery tray
- Smaller and sleeker redesign
- Utilizes four 18650 batteries (not included)
Authentic 28mm Plastique Dual 18650 Series Mechanical Box Mod - Plastique
$184.99
Authentic Plastique Dual 18650 Box Mod
Takes Two 18650 batteries (not included)
Fits 28mm RDA/RTA
"Blank" Button side, logo only
"Plastique" text engraving only.
Very Limited Inventory
No Returns unless factory defective within 14 days within purchase.
WARNING: THIS IS AN ADVANCE USER DEVICE AND SHOULD ONLY BE USED BY EXTREMELY EXPERIENCED USERS ONLY. NEVER FIRE THE DEVICE WITHOUT AN ATOMIZER ATTACHED. THE BATTERIES MUST BE PLACED IN THE CORRECT ORIENTATION, OR IT WILL SHORT CIRCUIT AND EXPLODE. THIS IS A SERIES BATTERY DEVICE. IT IS HIGHLY RECOMMENDED THAT YOU NEVER BUILD YOUR RESISTANCE LOWER THAN 0.5 OHMS. FAILURE TO DO SO WILL RESULT IN SERIOUS INJURY. REMEMBER, THAT A DUAL SERIES BATTERY SETUP WILL DOUBLE THE VOLTAGE OUTPUT OF A SINGLE CELL OR PARALLEL SETUP. THUS, A DUAL SERIES DEVICE LIKE THIS WILL OUTPUT UP TO 8.5 VOLTS. REMEMBER THIS FOR YOUR POWER AND BATTERY SAFETY CALCULATIONS. REMEMBER, THAT A SERIES BATTERY SETUP WILL NOT INCREASE THE DISCHARGE CURRENT LOAD. REGARDLESS OF HOW MANY CELLS ARE IN A SERIES BATTERY SETUP, THE MAXIMUM DISCHARGE CURRENT IS THE SAME AS WITH ONE CELL, TWO CELL, OR THREE CELLS. REMEMBER THIS FOR YOUR POWER AND BATTERY SAFETY CALCULATIONS.
By purchasing this device, You agree to indemnify, defend and hold harmless Wicks & Wires Vape Shoppe Inc. and our parent, subsidiaries, affiliates, partners, officers, directors, agents, contractors, licensors, service providers, subcontractors, suppliers, interns and employees, harmless from any claim or demand, including reasonable attorneys’ fees, made by any third-party due to or arising out of your breach of these Terms of Service or the documents they incorporate by reference, or your violation of any law or the rights of a third-party.
View full product details
Authentic 32mm Plastique Dual 18650 Series Mechanical Box Mod - Plastique
$184.99
Authentic Plastique Dual 18650 Box Mod
Takes Two 18650 batteries (not included)
Fits 32mm RDA/RTA
"Blank" Button side, logo only
"Plastique" text engraving only.
Very Limited Inventory
No Returns unless factory defective within 14 days within purchase.
WARNING: THIS IS AN ADVANCE USER DEVICE AND SHOULD ONLY BE USED BY EXTREMELY EXPERIENCED USERS ONLY. NEVER FIRE THE DEVICE WITHOUT AN ATOMIZER ATTACHED. THE BATTERIES MUST BE PLACED IN THE CORRECT ORIENTATION, OR IT WILL SHORT CIRCUIT AND EXPLODE. THIS IS A SERIES BATTERY DEVICE. IT IS HIGHLY RECOMMENDED THAT YOU NEVER BUILD YOUR RESISTANCE LOWER THAN 0.5 OHMS. FAILURE TO DO SO WILL RESULT IN SERIOUS INJURY. REMEMBER, THAT A DUAL SERIES BATTERY SETUP WILL DOUBLE THE VOLTAGE OUTPUT OF A SINGLE CELL OR PARALLEL SETUP. THUS, A DUAL SERIES DEVICE LIKE THIS WILL OUTPUT UP TO 8.5 VOLTS. REMEMBER THIS FOR YOUR POWER AND BATTERY SAFETY CALCULATIONS. REMEMBER, THAT A SERIES BATTERY SETUP WILL NOT INCREASE THE DISCHARGE CURRENT LOAD. REGARDLESS OF HOW MANY CELLS ARE IN A SERIES BATTERY SETUP, THE MAXIMUM DISCHARGE CURRENT IS THE SAME AS WITH ONE CELL, TWO CELL, OR THREE CELLS. REMEMBER THIS FOR YOUR POWER AND BATTERY SAFETY CALCULATIONS.
By purchasing this device, You agree to indemnify, defend and hold harmless Wicks & Wires Vape Shoppe Inc. and our parent, subsidiaries, affiliates, partners, officers, directors, agents, contractors, licensors, service providers, subcontractors, suppliers, interns and employees, harmless from any claim or demand, including reasonable attorneys’ fees, made by any third-party due to or arising out of your breach of these Terms of Service or the documents they incorporate by reference, or your violation of any law or the rights of a third-party.
View full product details
BREW #22M HARD STRAWBERRY ICE - BREWELL VAPORY
$34.99
This e-juice is profiled to taste like strawberry hard candy with strawberry jelly filling mixed with iced cold menthol. From start to finish, inhale to exhale, you will taste the strong strawberry flavoring followed by a hint of cool, which is very pleasant. Brew #22M by Hard Strawberry Ice by Brewell Vapory has a great throat hit, it is not too harsh, nor to soft. Since it is a menthol flavor, it does have a sharp throat hit that provides the nice throat tickle that everybody loves.
PG/VG: 30/70
View full product details
Replacment Glass for the Uwell 3 Tank - Uwell
$4.99
This is the authentic replacement glass for the Uwell Crown 3 Tank. View full product details
Riot - Modus
$35.99
Tangy lime glaze, crisp apple cider, milky cream, and crumbs on the exhale. A rich apple crumble cut with lime goodness.
PG/VG Ratio: MAX VG
View full product details
Fuchai Duo-3 2 Cover Version TC Mod - Sigelei
Sold Out
Sigelei Fuchai Duo-3 Dual / Triple Battery Temperature Control Box Mod
The Sigelei Fuchai Duo-3 TC Mod features the unique ability to choose from a dual or triple 18650 battery configuration with a simple swap of the battery cover. Choose from a powerful maximum wattage of 255 watts with the triple battery configuration or with a more lightweight and portable setup with the dual battery configuration which has a maximum wattage of 175 watts. Nickel 200, Titanium, Stainless Steel 316, 317 and TCR temperature control modes are available in both configurations. A detailed vaping interface is shown on the large 1.0" TFT color display screen that is both easy to read and understand. A large tactile fire button is utilized in conjunction with the lightweight zinc alloy construction for a precise and robust vaping experience. The Sigelei Fuchai Duo-3 requires (2) or (3) high amp 18650 batteries (sold separately) which is easily replaced using the locking battery door cover. A micro USB port is available for future firmware updates and charging. We recommend an external charger (sold separately) for optimal charging speeds.
Quick Links:
Premium E-Liquid
Features and Specs:
Choose from a Dual or Triple Battery Configuration
Dimensions: 3-5/16" x 1-5/8" x 1-1/4" (Dual Battery Configuration)
Dimensions: 3-5/16" x 1-5/8" x 1-13/16" (Triple Battery Configuration)
510 Threaded
Wattage Output: 10.0 - 175.0W (Dual Battery Configuration)
Wattage Output: 10.0 - 255.0W (Triple Battery Configuration)
Temperature Control: Nickel 200 (Ni200), Titanium (Ti), Stainless Steel 316, 317 (SS), TCR
Temperature Range: 100 - 300C / 200 - 570F
Resistance Range: 0.1 - 3.0ohm
Preheat Function
Puff Counter
Large Tactile Fire Button
1.0" TFT Color Display Screen
Detailed Operating Interface
Zinc Alloy Construction
Locking Battery Door Cover
Requires (2) or (3) High Amp 18650 Batteries (Sold Separately)
*All batteries must be the same brand and model. Discharge and recharge the batteries together for maximum efficiency*
*External charger recommended for optimal charging speeds*
Micro USB Charging Port (DC 5V/2.5A)
Firmware Upgradeable
Includes (1) Dual Battery Configuration Cover (Pre-installed) and (1) Triple Battery Configuration Cover View full product details
Maliboujee - Definitive
$29.99
A creamy Pina Colada with Jamaican Rum, Cantaloupe, Strawberry, Guava and Passion Fruit with a hint of lime.
PG/VG: 30/70
View full product details
Chillatte - Summer Chillin
$29.99
Some things are best vaped. Summer is not the same without a delicious iced cappuccino. Great Canadian Fog has really outdone themselves with this exciting flavor! Nothing says hot summer day like Chillatte!
PG/VG: 30/70
View full product details
Sherbet - Summer Chillin
$29.99
Everyone loves Ice cream, but what about Sherbet? Great Canadian Fog has released the most delicious flavor yet, Sherbet is a summertime classic and has rich flavors of orange and berry. This is the time to relax by the pool and vape on with Great Canadian Fog Sherbet!
PG/VG: 30/70
View full product details
Huckleberry - Cloudfire
$29.99
Mouth watering ripe berries baked into a light buttery crust with a sweet, decadent whipped topping.
PG/VG: 20/80
View full product details
SUBZEROX COMPETITION MOD - SUB OHM INNOVATIONS
$159.99
We didn't think they could do better than their SubZero Legendary and SubZero Shorty, but to our dismay they managed to prove us wrong. Not only is it cheaper than the Legendary and Shorty, but it hits substantially harder.
Specifications:
-Three Piece Clutch Contact
-Interchangeable Sleeve
-Hybrid 510 Connection
-Locking Switch
-High Flow Battery Safety Vents
-Reverse Battery Protection
-Internal Short Protection Sleeve
-25mm Diameter x 96mm Length
-Single 18650 Li-ion Battery (Not Included)
DISCLAIMER: Mechanical mods are for experienced vapers with access to meters and a working knowledge of Ohms Law, Watts Law, battery safety, and how general electricity works. Please ensure care is taken as to not cause damage nor harm to the atomizer, your battery, the vaping device, yourself, others, or personal property.
Wicks & Wires Vape Shoppe is not responsible for misuse of product, or dangerously low coil builds. Wicks & Wires Vape Shoppe is not liable for the use of improper batteries for your builds.
View full product details
Learn - Primal Elixir
$29.99
A Blood Orange Strawberry Lemonade.
PG/VG: 30/70
View full product details
Mister Sugarhorn - EZ Vape
$29.99
A Vanilla Custard Cannolli dusted with cinnamon.
PG/VG: 20/80
View full product details
OSUB Baby 80W TC Starter Kit - SmokTech
$74.95
The SMOK OSUB Baby 80W TC Starter Kit exemplifies SMOKTech's dedication towards development by delivering an upgraded rendition of the OSUB platform, now powered by a single 18650 battery with modern comprehensive functionalities. Maintaining compact size with top-of-the-line ergonomics, the OSUB Baby 80W features the squeeze-to-fire lateral C-Shaped firing bar that make general use and handling simple and easy. Integrated with an intuitive OLED screen with adjustment buttons and microUSB port directly below, the OSUB Baby is the perfect portable work-horse device. Internally, the device is powered by a single 18650 battery (SOLD SEPARATELY), accessed via snap-on battery cover for convenient access. with a maximum output of 80W with a firmware upgrade system, allowing for additional support and revisions. The OSUB Baby 80W implements a maximum output of 80W with a firmware upgrade system, and a suite of comprehensive temperature control setting and safety protection for well-rounded performance capability. Included in each set is the highly-appraised TFV8 Baby Beast Tank, featuring a range of 3mL juice reservoir, precision airflow control, signature hinged top-fill system, and utilizes the dynamic Baby Turbo Engines coil structure. Bringing improvements to one of the most beloved chassis in SMOK's progressive systems, the OSUB Baby 80W TC Starter Kit is one of the premier mid wattage starter kit in the market.
OSUB 80w Mod Specifications:
Wattage Range: 1W - 80W
Temperature Range: 200°F - 600°F / 100°C - 315°C
Resistance Range:
Voltage Range: 0.8V - 9.0V
Streamline Design
Lateral Fire Bar
Intelligent Atomizer Recognition
Puff Monitoring System
OLED Display
Zinc Alloy Construction
Micro USB Port (Charging & Updating)
Compact Design
Latched Battery Access Panel
Requires (1) 18650 Battery (Battery Sold Separately)
Protections: 12 Second Cut Off, Short Circuit, Overheating, Low Battery Warning
TFV8 Baby Beast Specifications:
Dimensions: 53*22mm
3.0mL Tank Capacity
Stainless Steel Construction
Glass Tank Section
Dual Cyclops Adjustable Airflow
Top Fill System
Wide Bore Delrin Drip Tip
Swivel Action Top Fill
Package Contents:
1 x OSUB Baby Mod
1 x TFV8 Baby
2 x V8 Baby-Q2 Core 0.4Ω Dual Coil (1 x Pre-Installed)
1 x Vapor Band
1 x Replacement Sealing Pad
4 x Spare O-Rings
1 x Micro USB Cable
1 x User Manual
1 x Warranty Card
View full product details
Fortune Cookie - Vape Take Out
$32.99
The one and only Fortune Cookie flavor.
PG/VG: 30/70
View full product details
Harambe - Excision
$32.99
Excision and Alt Zero come together to resurrect HARAMBE! He’s back and this time he’s brought a deliciously refreshing banana berry smoothie! Creamy bananas blended perfectly with wild red, black and blue berries hand picked from the Amazon jungle by Harambe himself. He lives on and we honor him through this...
PG/VG: 20/80
View full product details
Butter Pecan Toffee - 80V
$34.99
Imagine a warm and delicious custard pie chock full of pralines and shavings of toffee encased in a flaky, delicious crust.
PG/VG: 30/70
View full product details
Fodi 24 - HCigar
$48.99
The HCigar Fodi 24 rebuildable dripping tank atomizer packs a LOT of features into an incredibly flavourful yet innovative and attractive dual coil tank design.
Designed for big vapor production, while not compromising on flavour.
Easy fill design allows users to fill and clean the tank portion without disturbing the build on the top deck!
810 drip tip fits most drip tips designed to fit Kennedy, Goon, CSMNT, etc.
316 grade stainless steel and Pyrex (borosilicate) tank holds up to 2.5ml of liquid.
A clamp style two-post design with adjustable side fed air flow allows for extremely easy single coil builds with incredible flavour and cloud production.
The top coil deck design allows for a number of benefits compared to bottom coil designs, such as:
- Improved flavour (greater warmth) as it is closer to the user’s mouth, which results in less travel time between the coil and inhalation. This provides dripper-like flavour.
- Separation of the heating chamber from the liquid will prevent spoiling (darkening) of the liquid due to excessive heat contact.
- Separation of the liquid from the top deck allows users to drip directly on to the coils as desired, but can easily revert back to tank mode when set up like an auto-dripper.
FEATURES
- Double row multiple small hole air inlets allows improved flavour and cloud production.
- Easy fill design also allows easy cleaning of the tank without disturbing coil build.
- Large bore 810 drip tip accepts drip tips designed for Kennedy, Goon, and CSMNT.
- Two post design allows for extremely easy builds that automatically centers coils between the posts.
- Top coil deck design to create a dripper-like experience, and to separate heat from liquid chamber.
- Pyrex tank can handle any kind of liquid.
- Dual coil build design.
- Metal components made from 316 grade stainless steel.
- PEEK insulator underneath the positive post assembly can withstand high temperatures while preventing heat transfer to other areas of the tank.
- 2.5 ml capacity
- 24mm diameter
- 36mm tall (excluding drip tip).
- Available in either silver or black colours.
WARNING: It is highly recommend that you fully clean out this product before the first time you use it. While the factory does a decent job at removing dust, shavings, machining lubricants and greases, there is still the potential for trace elements to remain, and it is best recommended that you do an additional cleaning to meet your standard of cleanliness.
DISCLAIMER: Rebuildable atomizers are for experienced vapers with access to meters and a working knowledge of Ohms Law, Watts Law, battery safety, and how general electricity works. Please ensure care is taken as to not cause damage nor harm to the atomizer, your battery, the vaping device, yourself, others, or personal property.
Wicks & Wires Vape Shoppe is not responsible for misuse of product, or dangerously low coil builds. Wicks & Wires Vape Shoppe is not liable for the use of improper batteries for your builds.
View full product details
Maze V3 - HCigar
$44.99
The Maze V3 by HCigar is another high performance rebuildable dripping atomizer, the third in the Maze series of RDA's by HCigar. Each Maze RDA has a unique feature, and the V3 does not disappoint, with its innovative air flow tube design, which allows users to choose from one of two included air pipes which can be rotated to allow air to hit different areas of the coil. Also included, are two different 510 center pins which allow the option to use the Maze V3 as a standard dripper, or convert to a bottom feed atomizer (BF pin included in kit.)
Designed for single coil use only, an easy to build 2-post screw design allows for easy coil centering and builds. With the tornado style air flow pipe and the small, compressed chamber of the top cap, the Maze V3 is designed for pure flavour production.
Gold plated center pins will not corrode nor oxidize, which prevents fouling of your liquid.
WARNING: It is highly recommend that you fully clean out this product before the first time you use it. While the factory does a decent job at removing dust, shavings, machining lubricants and greases, there is still the potential for trace elements to remain, and it is best recommended that you do an additional cleaning to meet your standard of cleanliness.
DISCLAIMER: Rebuildable atomizers are for experienced vapers with access to meters and a working knowledge of Ohms Law, Watts Law, battery safety, and how general electricity works. Please ensure care is taken as to not cause damage nor harm to the atomizer, your battery, the vaping device, yourself, others, or personal property.
Wicks & Wires Vape Shoppe is not responsible for misuse of product, or dangerously low coil builds. Wicks & Wires Vape Shoppe is not liable for the use of improper batteries for your builds.
View full product details
Bottom Feed Pin for the Pandora RDA
$7.99
This will convert your Pandora RDA to be used on a squonking device.
Includes: Copper Bottom Feeder pin and compatible center post for the Pandora RDA.
View full product details
Copper X-Tension for XXX Mod - Vaperz Cloud
$84.99
Introducing the X-Tension from Vaperz Cloud
The X-Tension is an add on middle section for the XXX and future modular tube mods from Vaperz Cloud. The X-Tension allows the use of 2 18650, or 2 20700 batteries to be used in compatible mods to run in 8.4V series configuration.
The X-Tension is designed with a fixed contact plate in the middle so the batteries do not have to physically touch each other. This allows for use of various brands of batteries and a solid contact at all times.
The X-Tension also includes a sleeve for use of 18650 batteries and the sleeve can be removed when using 20700 batteries.
The X-Tension includes a thread on beauty ring for use in 20700 configurations to keep the sleek appearance of the setup regardless of different batteries being used.
WARNING: THIS IS AN ADVANCE USER DEVICE AND SHOULD ONLY BE USED BY EXTREMELY EXPERIENCED USERS ONLY. NEVER FIRE THE DEVICE WITHOUT AN ATOMIZER ATTACHED. THE BATTERIES MUST BE PLACED IN THE CORRECT ORIENTATION, OR IT WILL SHORT CIRCUIT AND EXPLODE. THIS IS A SERIES BATTERY DEVICE. IT IS HIGHLY RECOMMENDED THAT YOU NEVER BUILD YOUR RESISTANCE LOWER THAN 0.5 OHMS. FAILURE TO DO SO WILL RESULT IN SERIOUS INJURY. REMEMBER, THAT A DUAL SERIES BATTERY SETUP WILL DOUBLE THE VOLTAGE OUTPUT OF A SINGLE CELL OR PARALLEL SETUP. THUS, A DUAL SERIES DEVICE LIKE THIS WILL OUTPUT UP TO 8.5 VOLTS. REMEMBER THIS FOR YOUR POWER AND BATTERY SAFETY CALCULATIONS. REMEMBER, THAT A SERIES BATTERY SETUP WILL NOT INCREASE THE DISCHARGE CURRENT LOAD. REGARDLESS OF HOW MANY CELLS ARE IN A SERIES BATTERY SETUP, THE MAXIMUM DISCHARGE CURRENT IS THE SAME AS WITH ONE CELL, TWO CELL, OR THREE CELLS. REMEMBER THIS FOR YOUR POWER AND BATTERY SAFETY CALCULATIONS.
View full product details
MTO DNA75 Squonk Mod - C&C Mods
Sold Out
Made in Italy the MTO by C&C Mods is a single 18650 Squonk mod powered by the Evolv DNA75. Made from an anodized aluminum body with a unique logo inset on the back of the mod with stabalized wood the MTO measures in at 80mm L x 50mm W x 20mm D.
Specifications :
Made from Anodized Aluminium
Single 18650 battery (not included)
Evolv DNA 75 Chipset
Inset Stabilized Wood Logo
Size: 83mm x 50mm x 20mm
Made in Italy
Squonking Bottle not included
MTO DNA75 Squonk Mod - C&C Mods
Sold Out
Made in Italy the MTO by C&C Mods is a single 18650 Squonk mod powered by the Evolv DNA75. Made from an anodized aluminum body with a unique logo inset on the back of the mod with stabalized wood the MTO measures in at 80mm L x 50mm W x 20mm D.
Specifications :
Made from Anodized Aluminium
Single 18650 battery (not included)
Evolv DNA 75 Chipset
Inset Stabilized Wood Logo
Size: 83mm x 50mm x 20mm
Made in Italy
Squonking Bottle not included
MTO DNA75 Squonk Mod - C&C Mods
$499.99
Made in Italy the MTO by C&C Mods is a single 18650 Squonk mod powered by the Evolv DNA75. Made from an anodized aluminum body with a unique logo inset on the back of the mod with stabalized wood the MTO measures in at 80mm L x 50mm W x 20mm D.
Specifications :
Made from Anodized Aluminium
Single 18650 battery (not included)
Evolv DNA 75 Chipset
Inset Stabilized Wood Logo
Size: 83mm x 50mm x 20mm
Made in Italy
Squonking Bottle not included
MTO DNA75 Squonk Mod - C&C Mods
Sold Out
Made in Italy the MTO by C&C Mods is a single 18650 Squonk mod powered by the Evolv DNA75. Made from an anodized aluminum body with a unique logo inset on the back of the mod with stabalized wood the MTO measures in at 80mm L x 50mm W x 20mm D.
Specifications :
Made from Anodized Aluminium
Single 18650 battery (not included)
Evolv DNA 75 Chipset
Inset Stabilized Wood Logo
Size: 83mm x 50mm x 20mm
Made in Italy
Squonking Bottle not included
EVO DNA75 Squonk Mod - Art & Mod
Sold Out
Made in Italy with top notch quality and materials the Evo by Art & Mod is made of Delrin with Stainless Steel finishing. Powered by the Evolv DNA 75 the ergonomic shape of the EVO is a perfect fit in the hand for squonking.
Specifications :
- Made from Delrin and Stainless Steel
- Custom adjustable SS bottom feeding 510
- Single 18650 battery (not included)
- Evolv DNA 75 Chipset
- Semi flush buttons
- Laser engraved logo
- Size: 83 x 49.5 x 26 mm
- Made in Italy
- Squonking Bottle not included
Blue Slushee - Propaganda
$31.99
A Blue Slushee flavor.
PG/VG Ratio: 30/70
View full product details
Copious Crunch - Simply
$29.99
The ultimate fruity breakfast cereal blend, Copious Crunch will remind you of the old days of Saturday morning cereal, complete with milk.
PG/VG: 20/80
View full product details
Mysterious Medley - Simply
$29.99
Mysterious Medley, the newest flavor from Simply E-juice, blends a mixed berry taffy with a few mysterious, secret ingredients to create a sweet, tangy, chewy taffy blend that will make your mouth water while it keeps you guessing what’s in it.
PG/VG: 20/80
View full product details
Tenacious Toast - Simply
$29.99
Sweet cream, a dash of bakery cinnamon, light pastry notes and a splash of sweet maple syrup blended together to create Tenacious Toast, which can only be described as the most accurate French Toast e-liquid to date.
PG/VG: 20/80
View full product details
