WARNING: This product contains nicotine. Nicotine is an addictive chemical.


Hussar Legacy BF-Ready Rebuildable Dripping Atomizer - Hussar Vapes

Hussar Vapes

Please notify me when the item is back in stock.

Add to Wishlist

The Legacy by Hussar Vapes is an atomizer that Hussar Vapes is a bottom feed ready rebuildable dripping atomizer designed to suit vapers who use fruitier/fresher e-liquids while maintaining a lot of custard profile.

Airflow has been increased compared to the Hussar RDA 1.0, where the Legacy has two 7.14 mm2 air intake slots, totaling 14.28 mm2 in comparison to the Hussar RDA 1.0 which had two 4.6 mm2 air intakes for a total of 9.32 mm2 .

Building on the Legacy is easy and flexible, thanks to the 4-screw system that allows thoughtless single coils builds. This aids in not having to think about which way to wind the coil legs, either clockwise or counter-clockwise will work!

Screws have been specially designed and custom machined for the Legacy. In order to deliver a much more pleasant building experience, Hussar Vapes tested many different solutions and materials, deciding on a 1.8mm wide flat surface beneath the head of the screw to allow builders to easily use any wire desired without a need to bend it. Stainless steel is used for these screws in order to ensure longevity and reliability.

The Legacy is using a feeding system as seen before on the Hussar RDA 1.0 but improved; when the squonk bottle is pushed, the liquid is released from the sides of the pin location to saturate the cotton wick on both ends. Juice wells have also been widened in the deck of the Legacy to ensure more vaping time between each squonk. Excess liquid gets drained back through the pin, and approximately 1 to 1.5 mL of liquid is left in the atomizer deck (depending on how much cotton is placed in the well. A user can enjoy as much as 20 hits before the need to squonk again. This large well system also makes the Legacy much more difficult to over-squonk.

A solid non-BF pin is also included in the set for standard dripping usage.

This release has newer improved o-rings to solve the issue about users complaining about previous o-rings being so tight that the cap was difficult to remove.


  • 316 stainless steel construcction
  • 2x Black NBR70 15x1 o-rings
  • 1x Black NBR70 3x1 o-ring
  • 4x Custom machined stainless steel flat post screws
  • Handfinished for round, smooth edges
  • Hand finished satin deck
  • BF pin for side feeding system
  • Stainless steel low profile wide bore 510 drip tip included
  • Gold plated positive post for best conductivity and minimal oxidation.

Spare Parts:

  • 2x Black NBR70 15x1 o-rings
  • 1x Red silicone 15x1 o-ring
  • 1x Black NBR70 3x1 o-ring
  • 2x Custom machined stainless steel flat screws
  • Solid NON bottom feed pin


  • Custom made wooden box/510 stand by Custom Wood

NOTE: This product cannot be sold to Asia. If the intended destination of your purchase of this item is going to Asia, then your order for this item will be cancelled and refunded to you.

WARNING: It is highly recommend that you fully clean out this product before the first time you use it. While the factory does a decent job at removing dust, shavings, machining lubricants and greases, there is still the potential for trace elements to remain, and it is best recommended that you do an additional cleaning to meet your standard of cleanliness.

DISCLAIMER: Rebuildable atomizers are for experienced vapers with access to meters and a working knowledge of Ohms Law, Watts Law, battery safety, and how general electricity works. Please ensure care is taken as to not cause damage nor harm to the atomizer, your battery, the vaping device, yourself, others, or personal property.

Wicks & Wires Vape Shoppe is not responsible for misuse of product, or dangerously low coil builds. Wicks & Wires Vape Shoppe is not liable for the use of improper batteries for your builds.

Related Items